Stomra Guides

Stomra · Guide

Electrical design in Stomra

Place the devices, group them on a board, and the E plan, the group list, the cable metres and the IFC all come from the same model.

KitchenHall 22 DM2 N1A1 G6 EQLQ 3G1,5 +1,00 ög N1A1 E63 plan · power and lighting, drawn from the model GROUP LIST · N1A1 GruppSkyddKabelAnsluterm G5C10EQLQ 3G1,5Lights14 G6C10 30 mAEQLQ 3G1,5Outlets11 G7C16 30 mAEQLQ 3G2,5Hob8 read from the circuits each time it is drawn ON THE BOARD'S INSPECTOR G6 · 3 devices · 11 m · 2,1 kW · 1,2 % a hint appears when something needs a look
An E63 plan made from the floor plan: outlets, switches, light points and the board by their Swedish symbols, the arcs of each circuit and its home run with the tag. The group list beside it is a legend that reads the circuits.

One model, one drawing

In many tools the electrical drawing is one thing and the circuits are another: the arcs and home-run tags are drafted per view, and the group list is typed again. In Stomra you place the devices and say which circuit each is on and what feeds it. Everything else is read from that: the arcs and tags on the plan, the group list, the cable metres, the load and voltage drop, the checks and the IFC. Move an outlet and all of them follow.

The records Stomra writes are OpenEik's electrical records, so any tool that reads OpenEik reads the same installation. Electrical in OpenEik explains the format; this guide is about drawing it in Stomra.

Placing devices

The devices are in the Systems tab, in its Electrical group. Four buttons each open a menu of devices:

ButtonWhat it holds
SocketWall outlets with one, two or three sockets and IP44; outlets for the kitchen's and the laundry's machines, with their letters; the Perilex for the hob; data, aerial and speaker outlets, a wifi access point; CEE 16 and 32 A, a car charger, hard-wired machines and heaters.
SwitchOne-way, two-way, intermediate, kron and two-pole switches, dimmers, Plejd and KNX buttons, a presence detector.
LightCeiling outlets (DCL), ceiling and pendant lights, recessed spots, wall and outdoor lights, a track, LED panels, linear and high-bay luminaires.
BoardA board (elcentral), the meter cabinet, junction boxes, ceiling boxes and Big-box.
  1. Open a plan of the storey.
  2. Pick a device from one of the four menus. The status line says where it will go and at what height.
  3. Click by a wall for a wall device: it goes onto the nearest wall face within a metre, at its type's height over the floor, facing the room. A ceiling device goes where you click, at the ceiling.

Emergency lighting, for ceiling and wall, is an electrical device too, and can be put on a circuit like any light. It is also placed from the fire tools, and a fire plan that hides the electrical devices still draws it with the fire drawing's symbol and counts it in the fire legend.

A plan draws the devices as Swedish electrical drawings do: an outlet a filled half-disc on its wall with its number of sockets and its purpose beside it, a switch a dot with its flags, a light point a circle with a cross, a board a black bar with its name.

A device's properties

Select a device and the Inspector's Electrical part shows:

Device

Change it for another device. It keeps its place and the way it faces.

Purpose

The letters beside its symbol: DM dishwasher, SP cooker, AB worktop, TM washer, TT dryer, K/F fridge-freezer, SF cooker hood, MU microwave, BB Big-box.

Designation

Its reference designation (IEC 81346), as the drawings name it: a board N1A1, the meter cabinet A1.

Height

Read as on the drawings, such as +1,00 ög: over the floor.

Controls

On a switch, dimmer, button or sensor: the lights or loads it works. A light shows what it is worked by.

Circuit and Fed from

Which circuit it is on, and what it is fed from: the board, or the device before it.

A light's type also holds its light output, and a spotlight can be aimed. See Lights.

Boards and circuits

A circuit (a group, in Swedish practice) belongs to a board. Select the board, and under Circuits press Add circuit. A new circuit is named G1, G2 and so on, and starts as C10 with EQLQ 3G1,5. Each circuit has:

Each circuit's row says how many devices it feeds, its cable metres, its load and its voltage drop to the farthest device: 2 devices · 9,9 m · 4,2 kW · 2,4 %.

A board itself is fed from somewhere. Its Fed by names the circuit upstream: the supply for the main board, or a circuit on the board before it for a sub-board. The drop at each board is carried down to the boards it feeds.

Wiring and cable lengths

Wiring is not drawn by hand. Give each device its Circuit and what it is Fed from, and the plan draws what the circuit means:

Because each device names the one before it, a circuit can branch: a junction box or an outlet that feeds two others is where it splits.

Each leg's length is estimated until you draw its route: up from the device to an installation zone 2,4 m over the floor, along the plan's two axes, and down to the next device. The Inspector gives a device's leg and a board's circuits with their metres.

Cable carriers and cable routes

The Route button in the Electrical group draws two kinds of thing:

Most legs can stay estimated. Model the routes that matter: a main cable, a feeder to a sub-board, a run through a tray. Carriers can also ask for openings where they pass through a wall or a slab, with Request openings in the same tab.

E63 and E64 plans

The electrical drawings are made from a floor plan, as the ventilation and plumbing plans are. In the Systems tab, System plan holds:

E63 plan

Power and lighting (kraft och belysning): the building in halftone, the outlets, switches, lights and boards by their symbols, the circuits' arcs and home runs.

E64 plan

Data, tele and media: the data, aerial and speaker outlets and access points by their symbols.

Pipes and ducts are hidden on an E plan, and a ventilation or plumbing plan leaves the electrical devices out. A view whose discipline is Electrical draws the rest of the building as an underlay by itself.

The key and the group list

The Legend tool in an E plan places its key, Förklaringar: each device the plan shows, with its symbol, its name and how many there are. Set a legend to Electrical circuits and it is the group list (gruppförteckning): Grupp, Skydd, Kabel, Ansluter and metres for each circuit on the level. An RCBO reads as on Swedish lists, such as C10 JFB 30 mA typ A. Both are read from the model each time they are drawn, so they never need updating.

Hints and Check systems

Stomra looks at each circuit as you work and shows hints under it. Systems ▸ Check systems lists them for the whole project and selects the first.

HintFor example
A load beyond its protectionThe devices draw about 14 A on a C10.
A protection beyond its cableA C16 is more than EQLQ 3G1,5 carries in a wall or a conduit.
A voltage drop over 4 %About 4,6 % to the garage outlet, 38 m away.
Outlets with no RCDOutlets on the circuit, and no 30 mA RCD in front of it.
Data on a power circuitA data, aerial or speaker outlet given a power circuit.
Broken linksA circuit that names what is no longer there, or a feed that comes round in a loop.
Lights and switchesRoom by room: luminaires no switch controls, switches that control no light, rooms with no light.

These are hints to look at again, not a design and not a signed calculation. The cable's capacity is that of copper in a wall or a conduit (IEC 60364-5-52, reference method B2), the drop is computed along the estimated or modelled routes at a power factor of one. An electrician checks the design against the rules that apply.

Lights

A luminaire's type can say how much light it gives: luminous flux, colour temperature, beam angle and where the light goes. Which lights are on is a 3D view's lighting scene, and walk mode lights the building with it. A switch in the walk turns what it controls on and off. All of this is in Lights in the walk.

A spotlight, or any luminaire whose light goes down or up, can be aimed. In the Inspector under Aim, set its Tilt and its Turn, or press Aim at… and click the point its light should go through, in 3D or in a plan. Straight takes the aim away. A selected spotlight shows its cone in 3D, and a plan draws an aimed light's turn as an arrow beside its symbol. A type's Throw and its falloff, indoors or outdoors, let a floodlight at the foot of a façade light it to the top.

IFC, OpenEik and your assistant

An IFC export writes each device as the IFC class of its kind, an outlet, a switching device, a light fixture, a junction box or a distribution board, with its electrical properties. The circuits are written as a distribution system with one circuit per group, its devices assigned to it and the legs as connected ports, so a reader of the IFC can still ask what is on N1A1 G6. A car charger, which IFC has no class for, is written as an electric appliance.

Your assistant works with the same records: it can place devices, add circuits, connect devices to them, read what Check systems says of a board, and switch or aim lights. It leaves a device's size to its type, as you do. See Modelling with an AI assistant.