Stomra · Guide
Fixtures and furniture
WCs, basins, showers, kitchens, sofas and beds: shaped in 3D, drawn as a clean symbol in plans, and joined to the pipes.
Two kinds: fixtures and furniture
Fixtures
Systems ▸ Fixture. WCs, washbasins, sinks, showers, baths, floor drains, faucets and taps, washing machines, dryers, the water heater, radiators. Each carries the connections its pipes join, a product code (VK401, TS101) and its IFC class.
Furniture
Build ▸ Furniture and Build ▸ Kitchen. Sofas, an armchair, dining and coffee tables, chairs, beds, bedside tables, wardrobes, a desk, a bookshelf, a vanity under a basin, a shower's glass wall, and kitchen runs. It stands alone, without connections.
Every item is a type: a row with its kind, its sizes and its finish. The body in 3D, the symbol in plans, the outline in sections, the IFC class and the row in schedules all come from that one type, so a wider basin type gives a wider basin everywhere. Nothing is downloaded: Stomra builds each shape from the type's sizes.
Every furniture piece is always in the menu. A project gets the piece's type when the first one is placed, so projects without furniture stay free of furniture types.
The shapes are Stomra's own, made to look right at a drawing's and a walk's scale. They are not a particular maker's product.
Placing fixtures and furniture
- Open a plan on the level where the item goes.
- Choose the item from Systems ▸ Fixture or Build ▸ Furniture.
- Click where it goes. Near a wall, an item that belongs against one backs onto it, facing into the room: a WC, a basin, a sink, a bath, a shower or a machine within 600 mm of a wall face; a bed, a wardrobe, a desk, a shelf, a vanity or a glass wall onto the nearest wall. A sofa, a table or a chair faces the way the tool strip's rotation says.
Heights are set for you where they are usual: a hob's top at 900, a built-in oven at 150, a vanity 250 above the floor, faucets by their code. Change them in the Inspector when a project needs otherwise.
Kitchens as runs of cabinets
A kitchen is one run, not a dozen boxes. Choose Build ▸ Kitchen and click where the run starts and where it ends, as you draw a wall: its back goes on the wall and its front into the room. The length fills with modules: a sink with its mixer, the dishwasher beside it, drawers, a hob over a built-in oven, cabinets with doors and, where there is room, a fridge-freezer at the end.
- One oak worktop, its top at 900, runs over the base cabinets, cut for the sink and the hob. The plinth runs under them, set back.
- Wall cabinets hang above, with a gap over the hob for a hood.
- The sink, mixer, hob, oven, dishwasher and fridge are fixtures of their own, held by the run. They keep their connections and IFC classes, move when the run moves (pipes joined to them follow), and go when the run is deleted.
- Plans draw the worktop's outline, the lines between modules and the wall cabinets dashed; the sink, the hob's plates and the machines' letters (DM, KF) come from the fixtures.
A run is straight: an L-shaped kitchen is two runs. To change which modules a run has, or their widths, ask your assistant.
One item, every view
| View | What it draws |
|---|---|
| Plan | The item's symbol, never cut. Architectural plans show furniture; plans of other disciplines leave it out. A plan that hides the systems still keeps WCs, basins, sinks, showers, baths, washing machines (TM), floor drains and towel rails by their symbols, without codes, pipes or connections, as an architect's plan shows them. |
| Section, elevation | The item's simple outline, drawn as seen, never as a cut box. |
| 3D view | The shaped body: a WC's bowl, seat and flush plate, a basin's bowl and trap, chrome mixers, upholstered sofas, oak tables. At Coarse detail, the simple body. A piece that is small on the screen is drawn as a plain block of its size, and comes back whole as you zoom in. |
| Walk mode | Always the shaped body, with glazed porcelain, chrome, brushed steel, lacquer, woven fabric, oak grain and polished stone. |
| Schedules and IFC | One row, or one object, per item, with its kind and type. |
Connections to the pipes
Each fixture type carries its connections: the system, the size and the point on the body where the pipe meets it. Draw a pipe (Systems ▸ Pipe) and click on a fixture's connection to end it there; the plan marks each connection with a small circle.
| Fixture | Connections |
|---|---|
| WC, wall-hung (VK401) | S 110 · KV 12 |
| Washbasin (TS101) | S 50 · KV 12 · VV 12 |
| Kitchen sink | S 50 · KV 12 · VV 12 |
| Shower (BL301) | KV 12 · VV 12; the floor drain beside it (B101) takes S 75 |
| Bathtub (BL401) | S 50 · KV 12 · VV 12 |
| Washing machine | S 40 · KV 12 |
| Dishwasher | S 40 · KV 12 |
Joins that stay joined
- A pipe end that lies on a connection is joined to it, and Stomra keeps that join. An end you set higher or lower on purpose stays free.
- Move or turn the fixture and the joined pipe ends follow. Move a pipe end off the connection and it lets go.
- Delete a fixture and its pipes are not orphaned in silence: the checks (Systems ▸ Check systems) name the join whose fixture is gone. They also name a pipe on the wrong system's connection and a pipe smaller than its connection.
- Sizing hints for water and waste read the joins, so each pipe knows which fixtures it serves.
In IFC
Each item exports as what it is, so other tools read it right. See OpenEik and IFC for exports in general.
| Item | IFC class · type |
|---|---|
| WC, washbasin, sink, shower, bathtub | IfcSanitaryTerminal · TOILETPAN, WASHHANDBASIN, SINK, SHOWER, BATH |
| Floor drain | IfcWasteTerminal · FLOORTRAP |
| Mixer, tap | IfcValve · FAUCET, DRAWOFFCOCK |
| Dishwasher, fridge-freezer, washing machine, dryer, hob, oven | IfcElectricAppliance · DISHWASHER, FRIDGE_FREEZER, WASHINGMACHINE, TUMBLEDRYER, ELECTRICCOOKER |
| Sofa, table, chair, bed, desk, shelf | IfcFurniture · SOFA, TABLE, CHAIR, BED, DESK, SHELF |
| Wardrobe, vanity, shower screen, kitchen run | IfcFurniture · USERDEFINED, by name |
| A fixture's connection | IfcDistributionPort nested in its fixture; a joined pipe connects port to port (IfcRelConnectsPorts) |
Furniture also says whether it is built in (Pset_FurnitureTypeCommon IsBuiltIn): a wardrobe or a vanity is, a sofa is not. A kitchen run's cabinets and worktop are written as one piece of furniture.
Furnishing a room with your assistant
Every fixture and piece of furniture is in the catalogue an assistant reads, and it places them with the same commands the app uses, backing onto walls the same way. A room's type tells it what such a room usually holds:
| Room type | Usually holds |
|---|---|
| Bathroom | A WC, a basin with its mixer and vanity, a shower with its glass wall and floor drain, a towel rail |
| Kitchen | A kitchen run, a hood, a table and chairs |
| Laundry | A washer, a dryer, a drying cabinet, a utility sink, a drain |
| Bedroom | A 160 bed, two bedside tables, a wardrobe |
| Living room | A sofa, an armchair, a coffee table, a bookshelf |
| Office | A desk, a chair, a bookshelf |
| Hall | A wardrobe |
Ask, for example, "furnish bathroom 1.03 with what it is missing". The assistant reads what stands in the room and what is missing, places the rest in one batch and reads the room again.
Room to move
A project can set the space it wants kept free: a turning circle per room type, and the free depth in front of a WC, a basin, a bath, a wardrobe or a kitchen run. Stomra holds no figures of its own for this, because they depend on the rules the project follows (its country's building rules, an accessibility standard, the firm's own handbook). Ask your assistant to look them up and set them. With them set, a plan at Fine detail draws the free circle dashed, and your assistant, reading the rooms, is told what blocks the space in front of each item.
Room to move is a drawing aid. It is not an accessibility verification.
Keeping a model light
A shaped piece is drawn in every 3D view, in walk mode, in IFC and on the client portal, and some pieces weigh far more than others: most furniture is light, while a bookshelf full of books weighs as much as dozens of chairs. Stomra keeps working views quick by drawing small, far pieces as blocks, and a piece is drawn once for all the places it stands. When the model's furniture and equipment grow heavy, your assistant is told which kind carries the weight, and the client portal draws the heaviest kinds as plain boxes and says how many.
Do not stretch a bookshelf into a storage rack or a machine: build racks from columns and beams instead. A linked IFC that is too large for a link leaves its furniture out first, and says how many objects it left out.